Item FLI2

Fitlock Stainless steel/Galvanized

sample Fitlock Stainless steel/Galvanized 2

Press-fit fastening for wall and ceiling panels

A stainless steel system designed for applications requiring non-combustible materials, a minimal gap between panel and substrate, and the possibility of using thin panels.

sample Fitlock Stainless steel/Galvanized 2

The integrated washer protects the fastening point.

This configuration integrates the washer directly into the female component, which is recessed into the panel. The solution protects the system during handling and transport, keeping the fastening element protected and recessed within the panel.

The system consists of two components: the female component installed in the panel and the male component fixed to the substrate. The connection is made by applying pressure.

Non-combustible

Stainless steel components for applications requiring non-combustible materials.

3 mm adjustment

Multidirectional adjustment for easier positioning.

Reduced gap

Thin flanges and a low profile to minimize the distance from the substrate.

Thin panels

Suitable for panels with a minimum thickness of 9 mm.

3 mm
Adjustment in all directions.

The system configuration allows 3 mm of adjustment in all directions, facilitating correct positioning and alignment of the panels.

Designed for environments with specific requirements.

Fitlock Inox is designed for installing ceiling and wall panels in environments where non-combustible materials are required.

Marine

Marine

Construction

Construction

Automotive

Automotive

Furniture

Furniture

Aerospace

Aerospace

Low profile. Reduced distance between panel and substrate.

Thanks to its thin flanges and low-profile fastening system, Fitlock Inox minimizes the distance between the panel and the substrate.

It is suitable for thin panels, with a minimum thickness of 9 mm.

Two retention levels for different application requirements.

The system is available in Soft and Hard versions, featuring two male component configurations to adapt the retention force to different application requirements.

Soft

FLI2S configuration

Normal force required for disengagement: 120 N ±10%

Hard

FLI2H configuration

Normal force required for disengagement: 120 N ±10%

Two installation configurations.

The technical datasheet illustrates the 2 mm Gap and No Gap configurations, along with their respective installation cross-sections.

2 mm Gap
Installation with a 2 mm gap.

No Gap
Installation without an additional gap.

Installation in three steps.

Install the female component in the prepared recess in the panel, ensuring correct positioning and alignment. Install the male component on the substrate using the designated fixing points. Bring the panel towards the substrate and engage the system by applying pressure.

Pay attention to screw positioning

The technical datasheet specifies that the fixing holes of the male and female components must be offset by 60° to prevent the screws from overlapping.

Dimensions and specifications.

The following data is taken from technical datasheet FLI01-2060929-IT.

General specifications
ItemFLI2
MaterialSTAINLESS STEEL/GALVANIZED STEEL
Adjustment3 mm in all directions
Recess diameterØ 29 mm
Flat dimensionsØ 54 mm
Total weight20 g
Screws to useFlat countersunk head Ø 2.5 mm
Minimum panel thickness9 mm
sample Fitlock Stainless steel/Galvanized 2
ComponentSoftHard
MaleFLI2_MFLI2_MH
FemaleFLI2_FFLI2_F
Complete assemblyFLI2SFLI2H
Normal force required for disengagement120 N ±10%120 N ±10%

Official Reseller

We support you in your project

Request information on Fitlock Stainless steel/Galvanized 2

    File max size: 10 MB. Allowed types: pdf jpg jpeg png zip dxf dwg.
    [honeypot email move-inline-css:true]

    Discover also

    FAQ

    Questions? Answers.

    It is a stainless steel press-fit fastening system designed for installing ceiling and wall panels.

    It is designed for environments where non-combustible materials are required. The technical datasheet also specifies a reduced gap between the panel and the substrate and suitability for thin panels.

    Fitlock Inox is suitable for thin panels, with a minimum thickness of 9 mm.

    The system allows 3 mm of adjustment in all directions.

    The system is available in Soft and Hard versions, featuring two different male component configurations.

    The technical datasheet illustrates two configurations: 2 mm Gap and No Gap.

    The fixing holes of the male and female components must be offset by 60° to prevent the screws from overlapping.